|
tdae mp5d
Description
TDAe MP5D - VST Multipass Filter with LFO:
- Multipass Filter for LP, HP, BP, Notch and Peaking
- LFO for Cutoff with a max. speed of 2Hz
- LFO for Resonance with a max. speed of 2Hz
- Master-Section with Clipping
- The LFO Depth set is calculated by the settings for Cutoff/Resonance and will have a maximum range of the value between the Cutoff/Resonance settings and the highest (if higher than 50%) or the lowest (if lower than 50%) value, so that the LFO spins around the set value for Cutoff/Resonance.
An Example: If is set a Cutoff value of 75% and the Cutoff LFO-depth is set to 100%, the LFO will spin the cutoff between 50% and 100% with the set value for LFO-speed. That means, that a set value for Cutoff/Resonance of 0% or 100% will not affect a LFO modulation.
This release is donationware
free vst plugin, pc.
TDA - TENTION Digital Audio - VST Instruments and Effects
- Multipass Filter for LP, HP, BP, Notch and Peaking
- LFO for Cutoff with a max. speed of 2Hz
- LFO for Resonance with a max. speed of 2Hz
- Master-Section with Clipping
- The LFO Depth set is calculated by the settings for Cutoff/Resonance and will have a maximum range of the value between the Cutoff/Resonance settings and the highest (if higher than 50%) or the lowest (if lower than 50%) value, so that the LFO spins around the set value for Cutoff/Resonance.
An Example: If is set a Cutoff value of 75% and the Cutoff LFO-depth is set to 100%, the LFO will spin the cutoff between 50% and 100% with the set value for LFO-speed. That means, that a set value for Cutoff/Resonance of 0% or 100% will not affect a LFO modulation.
This release is donationware
free vst plugin, pc.
TDA - TENTION Digital Audio - VST Instruments and Effects
Category
Keywords
Date
Jan 16, 2007
Contact name
Email
Link ID
17150
Write a Review
Add to My Favorite
Refer it to Friend
Report Broken Link
Other links at Free VST plugins > filters
1. bugpass
BugPass 1.1 - is a a dual-function plug-in. Its primary job is to serve as a bandpass filter, with sliders which enable a quick visual reference to the size of the frequency band being passed through. However, by reversing the sliderpositions, BugPass will also serve as a notch filter, eliminating frequencies between the sliders while leaving the remaining frequencies intact.
free vst plugin, pc.
free vst plugin, pc.
Category:
2. resonator
Resonator: i applied the the same software and technique used to analyze vocal signals for formant values to a set of instrument samples.. highly technically innaccurate, but results entertaining. signal mixed subtly with dry source (hence no 100% wet function) gives a nice 'acoustic body resonance' effect.
in a tragic case of redundancy, i decided each band filter should also have it's own very short delay (well it takes time for that sound to bounce around inside that violin..) which is a bit off because the delay times are more in accordance of 5', 10'.. more.. distances (unless trimmers are at far left!) but still gives a good 'coloured' sound.. as such, also has an appliance as small room reverb ...
free vst plugin. pc
in a tragic case of redundancy, i decided each band filter should also have it's own very short delay (well it takes time for that sound to bounce around inside that violin..) which is a bit off because the delay times are more in accordance of 5', 10'.. more.. distances (unless trimmers are at far left!) but still gives a good 'coloured' sound.. as such, also has an appliance as small room reverb ...
free vst plugin. pc
Category:
3. sweepie
Sweepie is a simple filter effect it rotates 2 filters.
free vst plugin. pc
free vst plugin. pc
Category:
4. monfilter lt
Monfilter LT:
Monofilter provides a simple interface designed to convert a stereo signal below a specified frequency into a mono signal. The balance knob allows adjustment of the remaining stereo signal above the cutoff frequency.
Useful for ensuring that sounds are suitable for mastering to vinyl and keeping a check on LF signals in general, especially where stereo effects processing has been applied. free vst plugin, pc.
Monofilter provides a simple interface designed to convert a stereo signal below a specified frequency into a mono signal. The balance knob allows adjustment of the remaining stereo signal above the cutoff frequency.
Useful for ensuring that sounds are suitable for mastering to vinyl and keeping a check on LF signals in general, especially where stereo effects processing has been applied. free vst plugin, pc.
Category:
5. glow
GLow is a resonant low-pass filter. It is used to remove all frequencies from a signal above a given cut-off point.
Increasing the resonance of the filter causes the frequencies around the cut-off to be boosted.
Resonance can create large peaks in the output. Because of this, the GUI features a peak display showing the maximum peak output level. The peak display is reset by clicking on it.
Parameters
Gain: The gain applied to the incoming signal.
Cut Off: The cut-off frequency. Frequencies above this will be removed.
Res: The resonance of the filter.
free vst plugin. pc
Increasing the resonance of the filter causes the frequencies around the cut-off to be boosted.
Resonance can create large peaks in the output. Because of this, the GUI features a peak display showing the maximum peak output level. The peak display is reset by clicking on it.
Parameters
Gain: The gain applied to the incoming signal.
Cut Off: The cut-off frequency. Frequencies above this will be removed.
Res: The resonance of the filter.
free vst plugin. pc
Category:
Main Category
8
1995
551
332
212
6
787
52
2257
361
411
189
140
209
17
2320
74
119
3
171
34
145
105
31
14
14
1034
157
232
86
265
9
1050
148
241
131
312
244
344
15
73
212
127
68
406
532
2600
86
Top 10
Statistics
Links: 17322
Categories: 1112
Unique Outgoing Hits: 3957873
Pagerank Statistics
